INSTRINSIC SAFETY BARRIER

Series 9260 Ex i transmitter supply units can be used for the intrinsically safe operation of transmitters or intrinsically safe mA sources such as 4- wire transmitters. The device allows HART signals to be transmitted in both directions. The portfolio includes one- and two- channel devices and a variant for signal duplication.
Universal use for transmitters and mA sources (4- wire transmitter)Slim design  12.5 mm wide for one- and two- channel versionsCan be used for functional safety levels up to SIL 2 (IEC/ EN 61508)

Isolators 9260/11-11-10sIsolators 9270Isolators 9275Isolators 9282Isolators 9260/13-11-10s
Part Number Options/Accessories

We direct all our activities to cater the expectations of customers by providing them excellent quality products as per their gratification.

Large quantity of Pepperl+Fuchs Isolated Barriers K-Systems on stock

1-channel
• Output EEx ia IIC
• 24 V DC nominal supply voltage
• Device installation permissible in zone 2
• Conversion of current/voltage or voltage/current
• Elevation/Suppression of the "life zero"
• Accuracy 0.1 %
• EMC acc. to NAMUR NE 21 KFD2-CD-Ex1.32
The KFD2-CD-Ex1.32 transmits an electrical unit signal from the safe area to the hazardous area. The conversion of a current signal into a voltage signal and vice versa is possible. Current input option A current limit circuit in series to terminal 9 protects the device from damage. The max. voltage drop at the input is DC 4 V, allowing for the connection of several KFD2-CD32-Ex1.32 repeaters due to the low voltage drop in order to maintain multiple galvanically isolated outputs (signal duplication). Voltage input option The signal is transmitted to terminals 9 and 10 across an amplifier and the DC/DC converter within the allowable voltage range. A voltage limiter circuit protects the amplifier from incorrect input switching and overvoltage, but will draw current through a 50 mA fuse during operation. The fuse can be changed only by the manufacturer. Current output option The open circuit voltage is DC 24 V within the allowable supply voltage range at terminals 1 and 2. The max. load that can be applied is 850 ???. Voltage output option At least 20 mA is available within the allowable supply voltage range at terminals 1 and 2 which means that with 10 V output voltage, a load of at least 500 ??? must be connected
Used to drive I/P converters and valve positioners. Table: input/output options, type For options enclosed in parantheses, the transfer range for a base type is only partially used, i. e. 4 mA ... 20 mA from the base type 0 mA ... 20 mA.

NBB5-18GM40-Z3-300MM-V1 NBN8-12GM65-US-V12 NBN8-18GM60-A2-V1 NBB15-30GM30-E2NEB3-8GM40-A0-V1 NEB3-8GM40-E0-V1NBB3-V3-Z5-5M-Y NCB1.5-8GM40-ZO NCB2-12GM35-NO-V1NCB2-12GM40-ZONCB5-18GM40-ZONEB22-30GM60-E2-V1 NBB2-12GM40-Z0 NBB15-30GM50-WS NBB15-30GM60-A2NBB8-18GM60-A2-V1NBB5-18GM40-Z0 NBB1.5-8GM40-Z0 NCB4-12GM35-Z4NBB15-30GM50-E0-MNBB5-18GM50-A2-V1 NBB8-18GM50-E2-M NEN20-18GM50-E3-V1NJ5-18GM50-E3-V1NCB15-30GM50-Z4  NBB5-18GM60-WS  NBB5-18GM60-WO NBN25-30GM50-US NBN30-L2-E2-V1 
NJ30+U1+DW1-1 NCN15-M1K-NONJ15S+U4+N NJ25-50-N-5M NBB5-18GM60-I3 CBN15-30GK60-E2
NBN15-30GM60-I3 CJ1-12GK-N-5M NCB5-18GM40-NO-5M NCN15-30GM40-N0- 10M    NJ4-12GM-N NJ4-12GM-N 5M NCB2-V3-NO 
NBB5-18GM60-WS NBN40-U1K-E2-3G-3D    NBB20-U1-UU

KFD2-CRG2-Ex1.DTransmitter Power Supply
KFD2-GUT-Ex1.DTemperature Converter with Trip Values
KFU8-CRG2-Ex1.DTransmitter Power Supply
KFU8-GUT-Ex1.DTemperature Converter with Trip Values
KFD2-WAC2-Ex1.DStrain Gauge Converter
KFD2-WAC2-Ex1.D-Y1Strain Gauge Converter


KFD0-SCS-Ex1.55SMART Current Driver/Repeater
KFD2-SCD2-Ex1.LKSMART Current Driver
KFD2-SCD2-Ex2.LKSMART Current Driver
KCD2-SCD-Ex1SMART Current Driver
KFD0-CS-Ex1.50PRepeater
KFD0-CS-Ex1.51PCurrent Driver/Repeater
KFD0-CS-Ex2.51PCurrent Driver/Repeater
KCD2-SCD-Ex1.SPSMART Current Driver
KFD0-CS-Ex2.50P
Z786Zener Barrier
Z788.RZener Barrier
Z789Zener Barrier
Z796Zener Barrier
Z810Zener Barrier
Z813Zener Barrier
Z822Zener Barrier
Z828Zener Barrier
Z857Zener Barrier
Z864Zener BarrierZ878Zener BarrierZ887Zener BarrierZ888Zener Barrier
Z905Zener BarrierZ910Zener BarrierZ915Zener BarrierZ915.1KZener Barrier
Z960.FZ961.FZ966.FZ972Z978Z810.CLZ828.HZ828.H.FZ865Z865.FZ872Zener BarrierZ879.FZ879.H.FZener BarrierZ886Z887.FZener BarrierZ887.H.FZener BarrierZ888.HZener Barrier

KFD2-STC4-Ex2
< 2-channel isolated barrier
< 24 V DC supply (Power Rail)
< Input 2-wire SMART transmitters
< Output 0/4 mA ... 20 mA
< Terminals with test points
< Up to SIL 2 acc. to IEC 61508
This isolated barrier is used for intrinsic safety applications. The device supplies 2-wire SMART transmitters in a hazardous area. It transfers the analog input signal to the safe area as an isolated current value. Digital signals may be superimposed on the input signal in the hazardous or safe area and are transferred bi-directionally. If the HART communication resistance in the loop is too low, the internal resistance of 250 Ω between terminals 8 and 9 can be used. Test sockets for the connection of HART communicators are integrated into the terminals of the device.
Signal type Analog input
The device supports the following SMART protocols:
• HART
• BRAIN
• Foxboro 
Input signal 0/4 ... 20 mA
Output signal 0/4 ... 20 mA (overload > 25 mA)

ISOLATED BARRIERS  DIN RAIL MOUNTED
K-System isolated barriers guarantee safe, reliable, and effi cient signal transmission between your fi eld device and the control system. In addition to their inherent power limitation, these modules feature galvanic isolation between the signal loop and all other power loops. Pepperl+Fuchs off ers the most complete range of products to meet all your application and installation requirements.

KCD2-ST-Ex1.LB Switch Amplifier1-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR input, 2 active transistor outputs, Usable as signal splitter (1 input and 2 outputs), Reversible mode of operation, Line fault detection (LFD), Housing width 12.5 mm, Up to SIL 2 acc. to IEC 61508
KFA4-SR2-Ex1.W Switch Amplifier1-channel, Control circuit EEx ia IIC, Reversible mode of operation, 1 relay contact output (change-over contact), EMC acc. to NAMUR NE 21, LB/SC monitoring, Up to SIL 2 acc. to IEC 61508/IEC 61511
 KFA4-SR2-Ex1.W.LB Switch Amplifier1-channel, Control circuit EEx ia IIC, Reversible mode of operation, Output I: relay contact output (change-over contact), Output II: optionally signal output/fault signal, EMC acc. to NAMUR NE 21, LB/SC monitoring, Up to SIL 2 acc. to IEC 61508/IEC 61511
KFA4-SR2-Ex2.W Switch Amplifier2-channel, Control circuit EEx ia IIC, Reversible mode of operation, 1 relay contact output (change-over contact) per channel, EMC acc. to NAMUR NE 21, LB/SC monitoring, Up to SIL 2 acc. to IEC 61508/IEC 61511
 KFA5-DU-Ex1.D Switch Amplifier, Timer Relay1-channel isolated barrier, 115 V AC supply, Dry contact or NAMUR inputs, Relay contact and transistor output, Adjustable output timer functions from 10 ms ... 60 min, Input frequency up to 80 Hz; pulse divider up to 1 kHz, Reset function, Configurable by keypad, Line fault detection (LFD)
 KFA5-SR2-Ex2.W.IR Switch Amplifier2-channel isolated barrier, 115 V AC supply, Dry contact or NAMUR inputs, Latching relay contact output, Line fault detection (LFD)
KFA6-DU-Ex1.D Switch Amplifier, Timer Relay1-channel isolated barrier, 230 V AC supply, Dry contact or NAMUR inputs, Relay contact and transistor output, Adjustable output timer functions from 10 ms ... 60 min, Input frequency up to 80 Hz; pulse divider up to 1 kHz, Reset function, Configurable by keypad, Line fault detection (LFD)
KFA6-ER-Ex1.W.LB Conductivity Switch Amplifier1-channel isolated barrier, 230 V AC supply, Level sensing input, Adjustable range 1 k .. 150 k, Relay contact output, Fault relay contact output, Adjustable time delay up to 10 s, Minimum/maximum control, Line fault detection (LFD)
KFA6-SR2-Ex2.W.IR Switch Amplifier2-channel isolated barrier, 230 V AC supply, Dry contact or NAMUR inputs, Latching relay contact output, Line fault detection (LFD)
 KFD2-DU-Ex1.D Switch Amplifier, Timer Relay1-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR inputs, Relay contact and transistor output, Adjustable output timer functions from 10 ms ... 60 min, Input frequency up to 80 Hz; pulse divider up to 1 kHz, Reset function, Configurable by keypad, Line fault detection (LFD)

KFD2-ELD-Ex16 Ground Fault Detection 16-channel isolated barrier, 24 V DC supply (Power Rail), Analog or digtial field device inputs, Monitors leakage current, Fault relay contact output, LED status indication, Test circuit for validation, Parallel connection for easy integration, Conformal coating KFD2-SOT3-Ex1.LB.IO Switch Amplifier 1-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR inputs, Usable as signal splitter (1 input and 2 outputs), Isolated passive transistor output, non-polarized, Isolated passive fault output, non-polarized, Line fault detection (LFD), Reversible mode of operation, Up to SIL 2 acc. to IEC 61508

Zener barriers are a cost-eff ective solution for providing an intrinsically safe interface with field devices located in the hazardous area. As part of the intrinsic safety barrier family, Pepperl+Fuchs off ers two distinct zener barrier systems. The Z-System barriers are 12.5 mm wide and mount and ground directly to standard 35 mm DIN rail, while the SB-System barriers are the only termination board solution with pluggable modules available on the market. In addition to this wide product portfolio of housing and connection styles, we off er accessories for each application.

KCD2-SON-Ex1.R1 Switch Amplifier1-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR input, 2 passive transistor outputs (resistive), Application-specific outputs, Line fault transparency (LFT), Usable as signal splitter (1 input and 2 outputs), Housing width 12.5 mm, Up to SIL 2 acc. to IEC 61508
KCD2-SON-Ex1.R2 Switch Amplifier1-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR input, Application-specific outputs, Usable as signal splitter (1 input and 2 outputs), 2 passive transistor outputs (resistive), Line fault transparency (LFT), Housing width 12.5 mm, Up to SIL 2 acc. to IEC 61508
KCD2-SON-Ex1.R3 Switch Amplifier1-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR input, Application-specific outputs, Usable as signal splitter (1 input and 2 outputs), 2 passive transistor outputs (resistive), Line fault transparency (LFT), Housing width 12.5 mm, Up to SIL 2 acc. to IEC 61508
KCD2-SON-Ex2 Switch Amplifier2-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR inputs, 2 passive transistor outputs (resistive acc. to EN 60947-5-6), Line fault transparency (LFT), Housing width 12.5 mm, Up to SIL 2 acc. to IEC 61508
KCD2-SON-Ex2.R1 Switch Amplifier2-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR inputs, 2 passive transistor outputs (resistive), Application-specific outputs, Line fault transparency (LFT), Housing width 12.5 mm, Up to SIL 2 acc. to IEC 61508
KCD2-SON-Ex2.R2 Switch Amplifier2-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR inputs, Application-specific outputs, 2 passive transistor outputs (resistive), Line fault transparency (LFT), Housing width 12.5 mm, Up to SIL 2 acc. to IEC 61508

KCD2-SON-Ex2.R3 Switch Amplifier 2-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR inputs, Application-specific outputs, 2 passive transistor outputs (resistive), Line fault transparency (LFT), Housing width 12.5 mm, Up to SIL 2 acc. to IEC 61508 KCD2-SOT-Ex2.SP Switch Amplifier 2-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR inputs, 2 passive transistor outputs, Reversible mode of operation, Line fault detection (LFD), Housing width 12.5 mm, Connection via spring terminals with push-in connection technology, Up to SIL 2 acc. to IEC 61508 KCD2-SR-Ex1.LB.SP Switch Amplifier 1-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR inputs, Usable as signal splitter (1 input and 2 outputs), Relay contact output, Fault relay contact output, Line fault detection (LFD), Housing width 12.5 mm, Connection via spring terminals with push-in connection technology, Up to SIL 2 acc. to IEC 61508 KCD2-SR-Ex2.SP Switch Amplifier 2-channel isolated barrier, 24 V DC supply (Power Rail), Dry contact or NAMUR inputs, Relay contact output, Line fault detection (LFD), Housing width 12.5 mm, Connection via spring terminals with push-in connection technology, Up to SIL 2 acc. to IEC 61508

• AUTOMATION EXPO CHENNAI
• AUTOMATION EXPO MUMBAI